avr-libc
2.1.0
Standard C library for AVR-GCC
|
AVR Libc Home Page |
AVR Libc Development Pages |
||||
Main Page |
User Manual |
Library Reference |
FAQ |
Example Projects |
Macros | |
#define | ATOMIC_BLOCK(type) |
#define | NONATOMIC_BLOCK(type) |
#define | ATOMIC_RESTORESTATE |
#define | ATOMIC_FORCEON |
#define | NONATOMIC_RESTORESTATE |
#define | NONATOMIC_FORCEOFF |
c99
or gnu99
.The macros in this header file deal with code blocks that are guaranteed to be excuted Atomically or Non-Atmomically. The term "Atomic" in this context refers to the unability of the respective code to be interrupted.
These macros operate via automatic manipulation of the Global Interrupt Status (I) bit of the SREG register. Exit paths from both block types are all managed automatically without the need for special considerations, i. e. the interrupt status will be restored to the same value it had when entering the respective block (unless ATOMIC_FORCEON or NONATOMIC_FORCEOFF are used).
A typical example that requires atomic access is a 16 (or more) bit variable that is shared between the main execution path and an ISR. While declaring such a variable as volatile ensures that the compiler will not optimize accesses to it away, it does not guarantee atomic access to it. Assuming the following example:
There is a chance where the main context will exit its wait loop when the variable ctr
just reached the value 0xFF. This happens because the compiler cannot natively access a 16-bit variable atomically in an 8-bit CPU. So the variable is for example at 0x100, the compiler then tests the low byte for 0, which succeeds. It then proceeds to test the high byte, but that moment the ISR triggers, and the main context is interrupted. The ISR will decrement the variable from 0x100 to 0xFF, and the main context proceeds. It now tests the high byte of the variable which is (now) also 0, so it concludes the variable has reached 0, and terminates the loop.
Using the macros from this header file, the above code can be rewritten like:
This will install the appropriate interrupt protection before accessing variable ctr
, so it is guaranteed to be consistently tested. If the global interrupt state were uncertain before entering the ATOMIC_BLOCK, it should be executed with the parameter ATOMIC_RESTORESTATE rather than ATOMIC_FORCEON.
See Problems with reordering code for things to be taken into account with respect to compiler optimizations.
#define ATOMIC_BLOCK | ( | type | ) |
Creates a block of code that is guaranteed to be executed atomically. Upon entering the block the Global Interrupt Status flag in SREG is disabled, and re-enabled upon exiting the block from any exit path.
Two possible macro parameters are permitted, ATOMIC_RESTORESTATE and ATOMIC_FORCEON.
#define ATOMIC_FORCEON |
This is a possible parameter for ATOMIC_BLOCK. When used, it will cause the ATOMIC_BLOCK to force the state of the SREG register on exit, enabling the Global Interrupt Status flag bit. This saves a small amout of flash space, a register, and one or more processor cycles, since the previous value of the SREG register does not need to be saved at the start of the block.
Care should be taken that ATOMIC_FORCEON is only used when it is known that interrupts are enabled before the block's execution or when the side effects of enabling global interrupts at the block's completion are known and understood.
#define ATOMIC_RESTORESTATE |
This is a possible parameter for ATOMIC_BLOCK. When used, it will cause the ATOMIC_BLOCK to restore the previous state of the SREG register, saved before the Global Interrupt Status flag bit was disabled. The net effect of this is to make the ATOMIC_BLOCK's contents guaranteed atomic, without changing the state of the Global Interrupt Status flag when execution of the block completes.
#define NONATOMIC_BLOCK | ( | type | ) |
Creates a block of code that is executed non-atomically. Upon entering the block the Global Interrupt Status flag in SREG is enabled, and disabled upon exiting the block from any exit path. This is useful when nested inside ATOMIC_BLOCK sections, allowing for non-atomic execution of small blocks of code while maintaining the atomic access of the other sections of the parent ATOMIC_BLOCK.
Two possible macro parameters are permitted, NONATOMIC_RESTORESTATE and NONATOMIC_FORCEOFF.
#define NONATOMIC_FORCEOFF |
This is a possible parameter for NONATOMIC_BLOCK. When used, it will cause the NONATOMIC_BLOCK to force the state of the SREG register on exit, disabling the Global Interrupt Status flag bit. This saves a small amout of flash space, a register, and one or more processor cycles, since the previous value of the SREG register does not need to be saved at the start of the block.
Care should be taken that NONATOMIC_FORCEOFF is only used when it is known that interrupts are disabled before the block's execution or when the side effects of disabling global interrupts at the block's completion are known and understood.
#define NONATOMIC_RESTORESTATE |
This is a possible parameter for NONATOMIC_BLOCK. When used, it will cause the NONATOMIC_BLOCK to restore the previous state of the SREG register, saved before the Global Interrupt Status flag bit was enabled. The net effect of this is to make the NONATOMIC_BLOCK's contents guaranteed non-atomic, without changing the state of the Global Interrupt Status flag when execution of the block completes.